Lee's Summit

Corrective Action Required

01/27/2025

-Unit 205 approved Unit 207- firetape attic space, seal all gaps and penetrations

Corrective Action Required

03/24/2025

DEFICIENT EROSION CONTROL INSTALLATION. NO FURTHER INSPECTIONS UNTIL ADEQUATE EROSION CONTROL PROVIDED. -Re establish erosion control methods at perimeter, post address, clean silt from street

Corrective Action Required

06/10/2024

STOP WORK - NO FOOTING INSPECTION ON FILE.

Informational

06/12/2024

Approved by David Ainsworth on 5/29/24

Informational

06/12/2024

6/12/24 BMP in compliance at time of inspection

Corrective Action Required

06/10/2024

Backfill around foundation to provide access for inspection

Informational

06/12/2024

6/13/24 BMP in compliance at time of inspection

Informational

06/13/2024

6/18/24 BMP in compliance at time of inspection

Resolved

06/18/2024

Backfill around foundation to provide access for inspection

Corrective Action Required

07/22/2024

Inspection for firewall only: -Complete MEPs -Provide UL assembly details, number, and screw pattern information -City approved, stamped plans must be on site for all inspections

Corrective Action Required

07/22/2024

-Restore BMPs at perimeter of lot

Corrective Action Required

09/17/2024

INSPECTION, TESTING AND PURGING. AMENDED 7-945. The test pressure to be used shall be not less than one and one-half times the proposed maximum working pressure, but not less than 10 psig (68.9kPa) irrespective of design pressure. For welded piping, and for piping carrying gas at pressures in excess of fourteen (14) inches water column pressure, the test pressure shall not be less than 60 psig. Where the test pressure exceeds 125 psig (862 kPa gauge), the test pressure shall not exceed a value that produces a hoop stress in the piping greater than 50 percent of the specified minimum yield strength of the pipe.

Corrective Action Required

09/17/2024

-PROVIDE PERMANENT LABELS AT EACH METER -EXPOSE UFER GROUND CONNECTION-THIS MUST BE ACCESSIBLE AT ALL TIMES

Corrective Action Required

09/17/2024

Not ready -complete all Fireblocking before rescheduling

Corrective Action Required

09/17/2024

INSPECTION, TESTING AND PURGING. AMENDED 7-945. The test pressure to be used shall be not less than one and one-half times the proposed maximum working pressure, but not less than 10 psig (68.9kPa) irrespective of design pressure. For welded piping, and for piping carrying gas at pressures in excess of fourteen (14) inches water column pressure, the test pressure shall not be less than 60 psig. Where the test pressure exceeds 125 psig (862 kPa gauge), the test pressure shall not exceed a value that produces a hoop stress in the piping greater than 50 percent of the specified minimum yield strength of the pipe. -Gauge does not work

Corrective Action Required

09/17/2024

-PROVIDE PERMANENT LABELS AT EACH METER -UFER GROUND CONNECTION MUST BE ACCESSIBLE AT ALL TIMES

Corrective Action Required

09/17/2024

*Not Ready. Too many discrepancies between plans and on site conditions to perfom a complete inspection. This list shall serve as a general list for both units and is understood to be incomplete. -Install 5/8" anchor bolts at PFH per detail -Nail exterior sheathing at PFH header per detail -Land electrical at garage -Provide bocca plates and protection plates at all dwv 1.25" to face of framing or less -Back wall at dining not per plan and has no braced wall panel -Missing PFH at back corner -Protect electrical at island min of 6" above floor -NM insulation not landing inside of boxes min 1/2" multiple locations -Seal plate penetrations throughout -Nail all ceiling joists to rafters and rafters to plate per code -Nail all exterior corners and intersecting walls per code -Use approved fasteners at all stud shoes and straps -Protect dryer duct min 2" below plate line -Fireblock dead space at 2nd floor HVAC chase -Correct overbored or discontinous top plates throughout (dryer duct, return air, etc, dwv, etc.) -Trap arm length to be min 2 pipe size diameter at washer -Engineer to address rafters landing on knee wall and not connected to joists at top plate 2nd floor -Rafter not bearing on top plate second floor bathroom -Secure nm in attic space, garage and chases per code -Protect nm within 6' of attic access -Solid block between joists above load bearing walls -Provide vent to roof for all new fixtures -Any AAV must be accessible -Complete DWV in basement -Correct overbored studs throughout at bearing and non bearing walls -Remove closet wall and door in garage and revise plans -Revise firewall detail as previously discussed on rated assembly inspection -(2) walls on second floor changed location -Header size at rear wall not per plan -Roof supports in wrong location and landing on non bearing walls -Header at kitchen/dining supporting 2nd floor and exterior and ceilnig joists not on plans -Bearing wall on second floor is not above 1st floor LVL -Vertical vent stacks cannot recieve waste from water closets -Have engineer address all framing issues discussed on site with Mark Harding, revise and resubmit plans before any further inspections

Resolved

11/14/2024

-Restore BMPs at perimeter of lot

Corrective Action Required

09/25/2024

-PROVIDE PERMANENT LABELS AT EACH METER -UFER GROUND CONNECTION MUST BE ACCESSIBLE AT ALL TIMES

Corrective Action Required

09/25/2024

INSPECTION, TESTING AND PURGING. AMENDED 7-945. The test pressure to be used shall be not less than one and one-half times the proposed maximum working pressure, but not less than 10 psig (68.9kPa) irrespective of design pressure. For welded piping, and for piping carrying gas at pressures in excess of fourteen (14) inches water column pressure, the test pressure shall not be less than 60 psig. Where the test pressure exceeds 125 psig (862 kPa gauge), the test pressure shall not exceed a value that produces a hoop stress in the piping greater than 50 percent of the specified minimum yield strength of the pipe. -Gauge does not work

Corrective Action Required

09/25/2024

11/14/24 *Not Ready. Too many deficiencies and items not addressed from previous inspection. Complete items on this list before rescheduling. This list shall serve as a general list for both units and is understood to be incomplete. -Remove tyvek to expose nailing pattern at all braced walls -Install 5/8" anchor bolts at PFH per detail-Not done -Nail exterior sheathing at PFH header per detail-Not done -Land electrical at garage-Not done -Anchor bolts to be in middle third of plate at garage -Strap top plate lapped less than 24” at garage wall -Fur down ceiling joists at hvac in garage for R30 insulation -Provide bocca plates and protection plates at all dwv 1.25" to face of framing or less-Not done -Structural strap both sides load bearing stairwell wall at over bored top plate lapped less than 24” at garage -Use proper fasteners at stud shoes -Missing PFH at kitchen and living room-Provide engineered correction -NM insulation not landing inside of boxes min 1/2" multiple locations -Seal plate penetration at stairwell wall -Nail all ceiling joists to rafters and rafters to plate per code-not done -Nail all exterior corners and intersecting walls per code-Not done -Use approved fasteners at all stud shoes and straps -Protect dryer duct min 2" below plate line-not done -Fireblock dead space at 2nd floor HVAC chase -Correct overbored or discontinous top plates throughout (dryer duct, return air, etc, dwv, etc.)-not done -Trap arm length to be min 2 pipe size diameter at washer -Engineer to address rafters landing on knee wall and not connected to joists at top plate 2nd floor-not done -Rafter not bearing on top plate second floor bathroom-not addressed -Secure nm in attic space, garage and chases per code -Protect nm within 6' of attic access -Solid block between joists above load bearing walls-not done -Provide vent to roof for all new fixtures -Any AAV must be accessible -Complete DWV in basement -Correct overbored studs throughout at bearing and non bearing walls -Missing (3) 2x10 beam in kitchen per revised drawings -Missing (2) 11 7/8” LVLs at living/dining room/Stairwell per revised drawings -Roof supports in wrong location and landing on non bearing walls -Header at kitchen/dining supporting 2nd floor and exterior and ceiling joists not on plans -Bearing wall on second floor is not above 1st floor LVL -Vertical vent stacks cannot receive waste from water closets -Have engineer address all framing issues discussed on site with Mark Harding, revise and resubmit plans before any further inspections

Corrective Action Required

11/14/2024

11/22/24 **Inspection denied and stop-work issued. Insulation already installed at garage ceiling and floor rim without approval. Shall remove all insulation before scheduling an inspection 11/14/24 *Not Ready. Too many deficiencies and items not addressed from previous inspection. Complete items on this list before rescheduling. This list shall serve as a general list for both units and is understood to be incomplete. -Remove tyvek to expose nailing pattern at all braced walls -Install 5/8" anchor bolts at PFH per detail-Not done -Nail exterior sheathing at PFH header per detail-Not done -Land electrical at garage-Not done -Anchor bolts to be in middle third of plate at garage -Strap top plate lapped less than 24” at garage wall -Fur down ceiling joists at hvac in garage for R30 insulation -Provide bocca plates and protection plates at all dwv 1.25" to face of framing or less-Not done -Structural strap both sides load bearing stairwell wall at over bored top plate lapped less than 24” at garage -Use proper fasteners at stud shoes -Missing PFH at kitchen and living room-Provide engineered correction -NM insulation not landing inside of boxes min 1/2" multiple locations -Seal plate penetration at stairwell wall -Nail all ceiling joists to rafters and rafters to plate per code-not done -Nail all exterior corners and intersecting walls per code-Not done -Use approved fasteners at all stud shoes and straps -Protect dryer duct min 2" below plate line-not done -Fireblock dead space at 2nd floor HVAC chase -Correct overbored or discontinous top plates throughout (dryer duct, return air, etc, dwv, etc.)-not done -Trap arm length to be min 2 pipe size diameter at washer -Engineer to address rafters landing on knee wall and not connected to joists at top plate 2nd floor-not done -Rafter not bearing on top plate second floor bathroom-not addressed -Secure nm in attic space, garage and chases per code -Protect nm within 6' of attic access -Solid block between joists above load bearing walls-not done -Provide vent to roof for all new fixtures -Any AAV must be accessible -Complete DWV in basement -Correct overbored studs throughout at bearing and non bearing walls -Missing (3) 2x10 beam in kitchen per revised drawings -Missing (2) 11 7/8” LVLs at living/dining room/Stairwell per revised drawings -Roof supports in wrong location and landing on non bearing walls -Header at kitchen/dining supporting 2nd floor and exterior and ceiling joists not on plans -Bearing wall on second floor is not above 1st floor LVL -Vertical vent stacks cannot receive waste from water closets -Have engineer address all framing issues discussed on site with Mark Harding, revise and resubmit plans before any further inspections

Corrective Action Required

11/14/2024

INSPECTION, TESTING AND PURGING. AMENDED 7-945. The test pressure to be used shall be not less than one and one-half times the proposed maximum working pressure, but not less than 10 psig (68.9kPa) irrespective of design pressure. For welded piping, and for piping carrying gas at pressures in excess of fourteen (14) inches water column pressure, the test pressure shall not be less than 60 psig. Where the test pressure exceeds 125 psig (862 kPa gauge), the test pressure shall not exceed a value that produces a hoop stress in the piping greater than 50 percent of the specified minimum yield strength of the pipe. -Gauge does not work

Resolved

11/27/2024

Corrective Action Required

11/27/2024

Erosion control in compliance

Corrective Action Required

11/22/2024

Unit 205: -Install flashing above window trim -Strap top plate lapped less than 24” at garage wall -Vent master bathroom shower trap. Support plumbing at 4 ft or less -Fb duct chase from soffit and joist space -Provide 5/8” type X rock at fire separation wall inside duct chases and soffit space; take care of the rated wall before all-rough can be approved -Provide 4-stud pack at stair -Toe nail joists to wall top plates -Nail rear PFH wall sheathing to headers and rim -Protect refrigerator water line at bottom wall plate. Use BOCA strike plate -Fb laundry wall at top plate -Provide wall receptacle at master bedroom wall exceeding 2 ft -Washer plumbing outside of wall space -Protect water lines at master bathroom shower -Protect nm across studdings within 6' of attic access -Protect dryer duct min 2" below plate line -Provide direct illumination of basement stair treads per code -Gas test failed. No pressure -Provide a stud directly under (2)2x10 above bottom stair landing -Fb basement wall from all soffits -Provide venting for basement bathroom sink. Vent connection cannot be below trap weir -Provide stud shoes for basement non-bearing wall studs bored more than 60% -Vent half bathroom water closet per code. Cannot use the 3” waste stack to vent the water closet -Provide 5/8” type X rock at fire separation wall at back of furnace -Toe nail joists to wall sill plates -Staple wiring minimum 1.25” away from nailing surface -Remove insulation and expose the rim below the rear PFH walls **DO NOT INSULATE Unit 207: -Install flashing above window trim -Strap top plate lapped less than 24” at garage wall -Support plumbing above garage at 4 ft or less -Provide 5/8” type X rock at fire separation wall inside duct chases and soffit space; take care of the rated wall before all-rough can be approved -Vent 2nd floor bathroom tub trap -Reinforce notched joist (same location as above) -Fb duct chase from soffit and joist space -Protect water lines at half bathroom/duct chase wall -Provide 4-stud pack at stair -Provide full support for (2)2x10 above entry door header -Toe nail joists to wall top plates -Tighten down the PFH wall hold down nut at rear dining -Nail rear PFH wall sheathing to headers (with 3” grid pattern) and rim -Protect wiring at rear dining wall corner -Protect refrigerator water line at bottom wall plate. Use BOCA strike plate -Install stud shoe at laundry wall where bored more than 60% -Provide wall receptacle at master bedroom wall exceeding 2 ft -Protect nm across studdings within 6' of attic access -Protect dryer duct min 2" below plate line -Provide direct illumination of basement stair treads per code -Provide a stud directly under (2)2x10 above bottom stair landing -Fb basement wall from all soffits -Provide stud shoes for basement non-bearing wall studs bored more than 60% -Vent half bathroom water closet per code. Cannot use the 3” waste stack to vent the water closet -Provide 5/8” type X rock at fire separation wall at back of furnace -Toe nail joists to wall sill plates -Staple wiring minimum 1.25” away from nailing surface **DO NOT INSULATE

Corrective Action Required

11/27/2024

Unit 205: -Install flashing above window trim -Vent master bathroom shower trap. Support plumbing at 4 ft or less -Fb duct chase from soffit and joist space-seal gaps and penetrations -Provide 5/8” type X rock at fire separation wall inside duct chases and soffit space; take care of the rated wall before all-rough can be approved-Secure drywall and seal gaps -Provide wall receptacle at master bedroom wall exceeding 2 ft-seal plate penetrations -Protect water lines at master bathroom shower-DWV outside of shower wall -Provide a stud directly under (2)2x10 above bottom stair landing-Use stud grade material and nail 12" oc -Fb basement wall from all soffits-seal gaps -Strap load bearing wall both sides at top plate stairwell wall overbored for vent -Provide venting for basement bathroom sink. Vent connection cannot be below trap weir -Block between all ceiling joists above load bearing walls -Provide stud shoes for basement non-bearing wall studs bored more than 60%-Use proper nails -Protect DWV at stairwell wall -Egress windows in 2nd floor above 44"-must comply with R310 -Complete DWV in basement -Secure receptacle at garage -Engineer to provide specs for hold down devices used as alternative on back wall PFH locations **DO NOT INSULATE Unit 207: -Install flashing above window trim -Support plumbing above garage at 4 ft or less -Provide 5/8” type X rock at fire separation wall inside duct chases and soffit space; take care of the rated wall before all-rough can be approved -Reinforce notched joist (same location as above) (Garage) -Fb duct chase from soffit and joist space-Seal gaps -Protect water lines at half bathroom/duct chase wall -Provide 4-stud pack at stair-Use stud grade lumber -Tighten down the PFH wall hold down nut at rear dining -Protect wiring at rear dining wall corner -Protect refrigerator water line at bottom wall plate. Use BOCA strike plate -Install stud shoe at laundry wall where bored more than 60%-Use proper fasteners -Provide wall receptacle at master bedroom wall exceeding 2 ft-seal penetrations -Protect dryer duct min 2" below plate line -Provide a stud directly under (2)2x10 above bottom stair landing-Use stud grade lumber -Fb basement wall from all soffits-Seal gaps -Provide stud shoes for basement non-bearing wall studs bored more than 60%-Use nails -Vent half bathroom water closet per code. Cannot use the 3” waste stack to vent the water closet -Provide 5/8” type X rock at fire separation wall at back of furnace -Engineer to provide specs for hold down devices used as alternative on back wall PFH locations -Egress windows in 2nd floor above 44"-must comply with R310 **DO NOT INSULATE

Corrective Action Required

12/05/2024

Unit 205: -Fb duct chase from soffit and joist space-seal gaps and penetrations -Protect water lines at master bathroom shower-DWV outside of shower wall -Fb basement wall from all soffits-seal gaps -Provide stud shoes for basement non-bearing wall studs bored more than 60%-Use proper nails -Egress windows in 2nd floor above 44"-must comply with R310 -Complete DWV in basement -Engineer to provide specs for hold down devices used as alternative on back wall PFH locations **DO NOT INSULATE Unit 207: -Provide 5/8” type X rock at fire separation wall inside duct chases and soffit space; take care of the rated wall before all-rough can be approved-Seal gaps and penetrations -Fb duct chase from soffit and joist space-Seal gaps -Install stud shoe at laundry wall where bored more than 60%-Use proper fasteners -Provide wall receptacle at master bedroom wall exceeding 2 ft-seal penetrations -Protect dryer duct min 2" below plate line -Fb basement wall from all soffits-Seal gaps -Provide stud shoes for basement non-bearing wall studs bored more than 60%-Use nails -Provide 5/8” type X rock at fire separation wall at back of furnace -Engineer to provide specs for hold down devices used as alternative on back wall PFH locations -Egress windows in 2nd floor above 44"-must comply with R310

Corrective Action Required

12/10/2024

Unit 205: -DWV outside of shower wall-NOT ADDRESSED -Complete DWV at grinder pump (Can verify when complete) *OK to insulate, do not cover inspection items Unit 207: -Complete DWV at grinder pump (Can verify when complete)

Resolved

12/18/2024

Unit 205: -DWV outside of shower wall-NOT ADDRESSED -Complete DWV at grinder pump (Can verify when complete) *OK to insulate, do not cover inspection items Unit 207: -Complete DWV at grinder pump (Can verify when complete)

Corrective Action Required

11/27/2024

INSPECTION, TESTING AND PURGING. AMENDED 7-945. The test pressure to be used shall be not less than one and one-half times the proposed maximum working pressure, but not less than 10 psig (68.9kPa) irrespective of design pressure. For welded piping, and for piping carrying gas at pressures in excess of fourteen (14) inches water column pressure, the test pressure shall not be less than 60 psig. Where the test pressure exceeds 125 psig (862 kPa gauge), the test pressure shall not exceed a value that produces a hoop stress in the piping greater than 50 percent of the specified minimum yield strength of the pipe. -Gauge does not work

Corrective Action Required

01/17/2025

1/17/25 -no access

Resolved

01/22/2025

INSPECTION, TESTING AND PURGING. AMENDED 7-945. The test pressure to be used shall be not less than one and one-half times the proposed maximum working pressure, but not less than 10 psig (68.9kPa) irrespective of design pressure. For welded piping, and for piping carrying gas at pressures in excess of fourteen (14) inches water column pressure, the test pressure shall not be less than 60 psig. Where the test pressure exceeds 125 psig (862 kPa gauge), the test pressure shall not exceed a value that produces a hoop stress in the piping greater than 50 percent of the specified minimum yield strength of the pipe. -Gauge does not work

Resolved

01/22/2025

1/17/25 -no access

Corrective Action Required

07/22/2024

-Entire 1 hour rated separation wall has been covered without inspections on both units

Corrective Action Required

01/22/2025

-Unit 205 approved Unit 207- firetape attic space, seal all gaps and penetrations

Resolved

02/04/2025

Erosion control in compliance

Corrective Action Required

02/04/2025

2/4/25 EROSION CONTROL REQUIRED. EROSION CONTROL SHALL BE IN COMPLIANCE WITHIN TWO BUSINESS DAYS. -Provide erosion control methods at perimeter -Maintain gravel filter with min 6" lift of min 3/4" gravel -Clean silt and debris from street

Resolved

03/24/2025

3/24/25 EROSION CONTROL REQUIRED. EROSION CONTROL SHALL BE IN COMPLIANCE WITHIN TWO BUSINESS DAYS. -Provide erosion control methods at perimeter -Maintain gravel filter with min 6" lift of min 3/4" gravel -Clean silt and debris from street

Corrective Action Required

03/24/2025

DEFICIENT EROSION CONTROL INSTALLATION. NO FURTHER INSPECTIONS UNTIL ADEQUATE EROSION CONTROL PROVIDED. -Re establish erosion control methods at perimeter, post address, clean silt from street

Informational

03/24/2025

Pre-inspection Driveway forms and materials appear to meet specification.

Informational

03/24/2025

Pre-inspection Driveway forms and materials appear to meet specification. 03/26/25 Wednesday JMJ Driveway passed final inspection.