Lee's Summit

Corrective Action Required

06/09/2020

- POST ADDRESS - - MAINTAIN SILT FENCE - - SPREAD GRAVEL FILTER -

Informational

06/24/2020

- 3RD PARTY STRUCTURAL GARAGE SLAB SIGNED & SEALED BY CHARLES R LOGAN

Corrective Action Required

06/09/2020

-Deficient erosion control installation, shall be in compliance within two days -Remove trash from site -Remove overgrown weeds and vegetation

Corrective Action Required

10/05/2020

Inspection denied. City approved plans must be on site for all inspections

Resolved

10/06/2020

Inspection denied. City approved plans must be on site for all inspections

Corrective Action Required

10/06/2020

-Fire block horizontal to vertical at all soffits and furr outs -Ensure all anchor bolts are properly tightened, garage and basement -Anchor bolt required within 12” of plate splice. Minimum of 2 anchor bolts per plate, garage & basement -furr out ducts in garage for insulation -Fire block all top and bottom plate penetrations -Seal penetrations in return air stud and joist cavities -mid point support for all vertical 2” and smaller DWV piping, at entry closet & kitchen/bath wall -provide bottom plate for plumbing furr out in living room -Remove exterior trim at rear elevation to verify sheathing fastening grid per plan- the two 18” wall sections per 3/S505 -Provide Simpson HTT4 with 5/8" Ø A307 threaded rod embedded and epoxied 6" into foundation at rear elevation engineered wall section per plan 3/S505 -Install window in living room -Provide 8-2x6 studs at rear elevation, between back door and engineered wall section per plan -Address over bored floor joist above entry door -Solid wood fillers or shims shall be used to eliminate any space between the wall structure and door frame behind each hinge at exterior doors -Stud to stud and abutting studs at intersecting wall corners at braced wall panels 12” OC nailing -Fire block between floor levels at tubs -Provide plumbing nail plate protection in entry closet -NM Conductors required to be protected 6” AFF at floor penetrations -Provide box at range electrical termination -Complete bath exhaust ducts and termination to exterior per plan -Complete water distribution piping to master bath -Provide baffling and blocking to prevent insulation from obstructing attic ventilation per plan -Address header deflection master bedroom door -Ensure purlin & T brace nailing is per plan -Flash plumbing vent roof penetrations -maintain required airspace at gas vent insulation shield -Air barrier requirements per plan- under energy conservation notes, see table N1102.4.1.1, 2018 IRC -Where cable is run at angles with joists in unfinished basement it shall be permissible to secure cables not smaller than two 6 AWG or three 8 AWG conductors directly to the lower edges of the joists. Smaller cables shall be run either through bored holes in joists or on running boards. -No gas piping installed. Provide piping, connect to appliances per manufacturer installation instructions and pressure test -Complete HVAC line set -Identify white conductors to be used as ungrounded conductors at both termination points -Provide joist hangers above basement bath -Address DF #2 floor joists where plan specificities DF #1 -Provide solid blocking where joists are parallel with foundation per plan DO NOT INSULATE DO NOT ROCK RE-INSPECTION REQUIRED

Corrective Action Required

10/06/2020

No gas piping installed. Provide piping, connect to appliances per manufacturer installation instructions and pressure test

Corrective Action Required

10/06/2020

No gas piping installed. Provide piping, connect to appliances per manufacturer installation instructions and pressure test

Corrective Action Required

10/06/2020

-Ensure all anchor bolts are properly tightened, basement -Anchor bolt required within 12” of plate splice. Minimum of 2 anchor bolts per plate, basement -furr out ducts in garage for insulation -Fire block all top and bottom plate penetrations, upstairs bedroom plumbing top plate -Remove exterior trim at rear elevation to verify sheathing fastening grid per plan- the two 18” wall sections per 3/S505 -Provide Simpson HTT4 with 5/8" Ø A307 threaded rod embedded and epoxied 6" into foundation at rear elevation engineered wall section per plan 3/S505 -Address over bored floor joist above entry door -Solid wood fillers or shims shall be used to eliminate any space between the wall structure and door frame behind each hinge at exterior doors -Stud to stud and abutting studs at intersecting wall corners at braced wall panels 12” OC nailing -NM Conductors required to be protected 6” AFF at floor penetrations -Complete bath exhaust ducts and termination to exterior per plan -Complete water distribution piping to master bath -Address header/top plate deflection master bedroom door -Ensure purlin & T brace nailing is per plan -Flash plumbing vent roof penetrations -maintain required airspace at gas vent insulation shield -Air barrier requirements per plan- under energy conservation notes, see table N1102.4.1.1, 2018 IRC -Where cable is run at angles with joists in unfinished basement it shall be permissible to secure cables not smaller than two 6 AWG or three 8 AWG conductors directly to the lower edges of the joists. Smaller cables shall be run either through bored holes in joists or on running boards. -No gas piping installed. Provide piping, connect to appliances per manufacturer installation instructions and pressure test -Complete HVAC line set -Identify white conductors to be used as ungrounded conductors at both termination points -Provide joist hangers above basement bath -Address DF #2 floor joists where plan specificities DF #1 -Provide solid blocking where joists are parallel with foundation per plan DO NOT INSULATE DO NOT ROCK RE-INSPECTION REQUIRED

Corrective Action Required

10/12/2020

-Ensure all anchor bolts are properly tightened, basement -Anchor bolt required within 12” of plate splice. Minimum of 2 anchor bolts per plate, basement -furr out ducts in garage for insulation -Fire block all top and bottom plate penetrations, upstairs bedroom plumbing top plate -Remove exterior trim at rear elevation to verify sheathing fastening grid per plan- the two 18” wall sections per 3/S505 -Provide Simpson HTT4 with 5/8" Ø A307 threaded rod embedded and epoxied 6" into foundation at rear elevation engineered wall section per plan 3/S505 -Address over bored floor joist above entry door at plumbing penetration -Solid wood fillers or shims shall be used to eliminate any space between the wall structure and door frame behind each hinge at exterior doors -Stud to stud and abutting studs at intersecting wall corners at braced wall panels 12” OC nailing -Complete bath exhaust ducts and termination to exterior per plan -Complete water distribution piping to master bath -Address header/top plate deflection master bedroom door -Ensure purlin & T brace nailing is per plan -Flash plumbing vent roof penetrations -maintain required airspace at gas vent insulation shield -Air barrier requirements per plan- under energy conservation notes, see table N1102.4.1.1, 2018 IRC -Provide gas piping pressure test -Complete HVAC line set -Identify white conductors to be used as ungrounded conductors at both termination points -Provide joist hangers above basement bath -Address DF #2 floor joists where plan specificities DF #1 DO NOT INSULATE DO NOT ROCK RE-INSPECTION REQUIRED

Corrective Action Required

10/06/2020

pressure test piping

Corrective Action Required

10/20/2020

-Ensure all anchor bolts are properly tightened, basement -Anchor bolt required within 12” of plate splice. Minimum of 2 anchor bolts per plate, basement -Remove exterior trim at rear elevation to verify sheathing fastening grid per plan- the two 18” wall sections per 3/S505 -Provide Simpson HTT4 with 5/8" Ø A307 threaded rod embedded and epoxied 6" into foundation at rear elevation engineered wall section per plan 3/S505 -Complete water distribution piping to master bath -Provide gas piping pressure test -Complete HVAC line set -Identify white conductors to be used as ungrounded conductors at both termination points -Provide joist hangers above basement bath UNABLE TO ACCESS BASEMENT DUE TO STANDING WATER 11/2/2010 OK TO INSULATE DO NOT ROCK RE-INSPECTION REQUIRED

Corrective Action Required

11/02/2020

-Still to verify fastening grid at rear elevation engineered wall project per plan 3/S505 -Provide gas piping pressure test -Complete HVAC line set OK TO ROCK

Resolved

11/03/2020

pressure test piping

Resolved

11/03/2020

No gas piping installed. Provide piping, connect to appliances per manufacturer installation instructions and pressure test

Informational

11/17/2020

PRE POUR INSPECTION The forms are set and there appears to be sufficient compacted aggregate.

Informational

11/17/2020

PRE POUR INSPECTION The forms are set and there appears to be sufficient compacted aggregate.

Informational

11/17/2020

PRE POUR INSPECTION The forms are set and there appears to be sufficient compacted aggregate.

Informational

11/17/2020

PRE POUR INSPECTION The forms are set and there appears to be sufficient compacted aggregate.

Corrective Action Required

09/16/2020

-Erosion control requires continuous maintenance. Reestablish methods within two business days -Immediate Street clean up required -No further inspections until complete

Corrective Action Required

12/04/2020

-Erosion control requires continuous maintenance. Reestablish methods within two business days -Immediate Street clean up required -No further inspections until complete

Resolved

01/29/2021

-Still to verify fastening grid at rear elevation engineered wall project per plan 3/S505 -Provide gas piping pressure test -Complete HVAC line set OK TO ROCK

Corrective Action Required

01/29/2021

-all outstanding fees must be paid in full -Provide as graded plot plan for review/approval -Remove excavation spoils -Final grade and sod -Maintain erosion control until sod is in place -Remove debris from the street and sidewalk -Complete building façade -Provide gutters and downspouts -downspouts and sump piping to discharge minimum 36 inches from foundation -All main or front entry doors to dwelling units shall be arranged so that the occupant has a view of the area immediately outside the door without opening the door. The view may be provided by a door viewer having a field of view of not less than one hundred eighty (180) degrees, by window(s), or by view port(s). -Seal top and sides of exterior lighting exposed to the elements and at AC disconnect -Seal all exterior penetrations -Identify white insulated conductor used as current carrying conductor at both points of termination, condensing unit circuit -install anti tip device at range -GFCI protection of dishwasher circuit required -label single receptacle dedicated circuits in unfinished basement as non gfci protected -All 120V single phase 15 & 20A circuits in kitchens and laundry areas require AFCI protection -cap future bathroom DWV stub in basement -GFCI protection of laundry circuit required -All front mandoor entrances shall be protected with a minimum of one light outlet having a minimum of sixty (60) watts of lighting (or energy efficient equivalent). Those fixtures placed below eight (8) feet shall be fixtures manufactured such that the light source is not "readily accessible" as defined in the adopted National Electrical Code (NEC).

Corrective Action Required

01/29/2021

-Provide as graded plot plan for review/approval -Remove excavation spoils -Final grade and sod -Maintain erosion control until sod is in place -Remove debris from the curb/gutter and sidewalk -Complete building façade -Provide gutters and downspouts -downspouts to discharge minimum 36 inches from foundation -All main or front entry doors to dwelling units shall be arranged so that the occupant has a view of the area immediately outside the door without opening the door. The view may be provided by a door viewer having a field of view of not less than one hundred eighty (180) degrees, by window(s), or by view port(s). -Seal top and sides of exterior lighting exposed to the elements -Identify white insulated conductors used as current carrying conductors at both points of termination, AC disconnect -repair yard across the road from water service installation TCO VALID THROUGH 03/01/2021

Corrective Action Required

02/01/2021

-Provide as graded plot plan for review/approval -Remove excavation spoils -Final grade and sod -Maintain erosion control until sod is in place -Remove debris from the curb/gutter and sidewalk -Complete building façade -Provide gutters and downspouts -downspouts to discharge minimum 36 inches from foundation -All main or front entry doors to dwelling units shall be arranged so that the occupant has a view of the area immediately outside the door without opening the door. The view may be provided by a door viewer having a field of view of not less than one hundred eighty (180) degrees, by window(s), or by view port(s). -Seal top and sides of exterior lighting exposed to the elements -Identify white insulated conductors used as current carrying conductors at both points of termination, AC disconnect -repair yard across the road from water service installation TCO EXTENSION VALID THROUGH 04/01/2021 DUE TO WEATHER CONDITIONS

Corrective Action Required

12/08/2020

Excavation spoils from foundation installation is being removed by ABI corporation. Trucks are traveling through the green space behind the property, any damage to the green space will require restoration to original condition. Mud and debris are being tracked from river trail road through the subdivision nearly to Pryor Road, I have notified Carla with ABI that immediate Street clean up is required

Corrective Action Required

04/07/2021

-The temporary certificate of occupancy has expired at this address. A permit extension request must be submitted in writing with the expected date of completion. After the request is submitted, please schedule an occupancy inspection so the inspector may review current site conditions and either approve or deny the request. -Maintenance of erosion control methods is required until sod is in place. Streets and sidewalks must remain free of silt and debris.

Corrective Action Required

02/22/2021

-Provide as graded plot plan for review/approval -Remove excavation spoils -Final grade and sod -Maintain erosion control until sod is in place -Remove debris from the curb/gutter and sidewalk -Complete building façade -Provide gutters and downspouts -downspouts to discharge minimum 36 inches from foundation -All main or front entry doors to dwelling units shall be arranged so that the occupant has a view of the area immediately outside the door without opening the door. The view may be provided by a door viewer having a field of view of not less than one hundred eighty (180) degrees, by window(s), or by view port(s). -Seal top and sides of exterior lighting exposed to the elements -Identify white insulated conductors used as current carrying conductors at both points of termination, AC disconnect -repair yard across the road from water service installation TCO EXTENSION VALID THROUGH 04/01/2021 DUE TO WEATHER CONDITIONS

Corrective Action Required

05/18/2021

The temporary certificate of occupancy has expired at this address. If remaining correction items are complete please schedule an occupancy inspection. If remaining correction items are not complete a permit extension request must be submitted in writing with the expected date of completion.

Corrective Action Required

05/18/2021

-Provide as graded plot plan for review/approval

Resolved

06/29/2021

The temporary certificate of occupancy has expired at this address. If remaining correction items are complete please schedule an occupancy inspection. If remaining correction items are not complete a permit extension request must be submitted in writing with the expected date of completion.