Lee's Summit

DE C&O #11 Pavement Thickness

Private parking lots shall follow Article 8 of the Unified Development Ordinance for pavement thickness and base requirements.

DE Commercial Detention Basin

The applicant shall submit and the City shall accept an “As-built / As-graded” detention basin plan prior to issuance of any occupancy permit for the proposed development.

DE Contact Field Eng. Inspector

Prior to the commencement of any construction activities, the Contractor shall contact Field Engineering Inspections at (816) 969-1200 to coordinate a preconstruction meeting / conference with the assigned Field Engineering Inspector.

DE Engineers Estimate

The Engineer’s Estimate of Probable Construction Costs has been accepted for this project, and the Engineering Plan Review and Inspection Fee (which is calculated as 3% of the total infrastructure cost plus a water test inspection fee(s)), and the water tap and meter setup fee have been included. These must be paid prior to the issuance of an infrastructure permit and/or the final processing of a building permit. $83,788.02

DE Future Repair Work

Please be aware that any future repair work to public infrastructure (e.g., water main repair, sanitary sewer repair, storm sewer repair, etc.) within public easements will not necessarily include the repair of pavement, curbing, landscaping, or other private improvements which are located within the easement.

MISC

It is recommended that retaining walls not be constructed over private fire lines.

Please label the detention basin prominently with a label of BMP.

Include the required, designed and as-built volumes for the basin.

Miscellaneous Correction

PLATTING. Because the proposed building crosses an existing lot line, no building permit shall be issued for the proposed building until the associated final plat (Appl. #PL20330-066) that removes said lot line has been approved and recorded. The associated final plat is currently scheduled for the May 25, 2023, Planning Commission meeting and City Council ordinance approval on June 13, 2023. This comment is inforrmational.

Miscellaneous Correction

MECHANICAL EQUIPMENT. A note was added indicating that RTU locations will be determined at a later time for each individual tenant space for the spec building. Please note the following requirements that will be reviewed for compliance at the time of tenant finish building permit review: - To comply with City ordinance, RTUs shall be fully screened from view on all sides to a height at least equal to the height of the units being screened. Please take into account the added height of the curbs on which the RTUs will sit.

Miscellaneous Correction

For information only- 3206.7.2 Where located. Where exterior walls surrounding high-piled storage areas face fire apparatus access roads, such walls shall be provided with fire department access doors. 3206.7.5 Number of doors required. The required fire department access doors shall be distributed such that the lineal distance between adjacent fire department access doors does not exceed 125 feet (38 100 mm) measured center to center.

Water Supply

IFC 507.1 - An approved water supply capable of supplying the required fire flow for fire protection shall be provided to premises upon which facilities, buildings or portions of buildings are hereafter constructed or moved into or within the jurisdiction. Action required- Confirm with Water Utilities there is adequate fire flow per IFC Table B105.1(2) with a 50% reduction allowed for an automatic fire sprinkler. Not addressed in 4/21/ 2023 comment letter. Not addressed in 5/19/2023 comment letter.

Miscellaneous Correction

Provide cleanouts per 2018 IPC 708.1 thru 708.1.3. 4/24/23 - CO provided in yard. CO will also be required near exit from building. Deferred to MEP building permit submission.

Miscellaneous Correction

All ground and roof mounted HVAC and/or electrical generators must be screened on all 4 sides per Unified Development Ordinance Article 8, Sections 8.180.E & F. We highly recommend coordinating this with your MEP design team at this phase to avoid problems with construction. Questions on this should be directed to Hector Soto - 816.969.1600 or Hector.Soto@CityofLS.net. 4/24/23 - Not addressed. Deferred to building permit.

DE C&O #11 Pavement Thickness

Private parking lots shall follow Article 8 of the Unified Development Ordinance for pavement thickness and base requirements.

DE Contact Field Eng. Inspector

Prior to the commencement of any construction activities, the Contractor shall contact Field Engineering Inspections at (816) 969-1200 to coordinate a preconstruction meeting / conference with the assigned Field Engineering Inspector.

DE Future Repair Work

Please be aware that any future repair work to public infrastructure (e.g., water main repair, sanitary sewer repair, storm sewer repair, etc.) within public easements will not necessarily include the repair of pavement, curbing, landscaping, or other private improvements which are located within the easement.

MISC

It is recommended that retaining walls not be constructed over private fire lines.

DE Commercial Detention Basin

The applicant shall submit and the City shall accept an “As-built / As-graded” detention basin plan prior to issuance of any occupancy permit for the proposed development.

DE Engineers Estimate

The Engineer’s Estimate of Probable Construction Costs has been accepted for this project, and the Engineering Plan Review and Inspection Fee (which is calculated as 3% of the total infrastructure cost plus a water test inspection fee(s)), and the water tap and meter setup fee have been included. These must be paid prior to the issuance of an infrastructure permit and/or the final processing of a building permit. $83,788.02

Miscellaneous Correction

The roundabout at Independence and Town Centre is expected to be constructed late 2023 or 2024. A connection from the proposed public sidewalk to the crosswalk ramps at the intersection needs to be constructed.

Miscellaneous Correction

PLATTING. Because the proposed building crosses an existing lot line, no building permit shall be issued for the proposed building until the associated final plat (Appl. #PL20330-066) that removes said lot line has been approved and recorded. The associated final plat is currently scheduled for the May 25, 2023, Planning Commission meeting and City Council ordinance approval on June 13, 2023. This comment is inforrmational.

Miscellaneous Correction

MECHANICAL EQUIPMENT. A note was added indicating that RTU locations will be determined at a later time for each individual tenant space for the spec building. Please note the following requirements that will be reviewed for compliance at the time of tenant finish building permit review: - To comply with City ordinance, RTUs shall be fully screened from view on all sides to a height at least equal to the height of the units being screened. Please take into account the added height of the curbs on which the RTUs will sit.

Code Statement

All issues pertaining to life safety and property protection from the hazards of fire, explosion or dangerous conditions in new and existing buildings, structures and premises, and to the safety to fire fighters and emergency responders during emergency operations, shall be in accordance with the 2018 International Fire Code.

Fire Lanes - Marking

IFC 503.3 Marking. Where required by the fire code official, approved signs or other approved notices or markings that include the words NO PARKING—FIRE LANE shall be provided for fire apparatus access roads to identify such roads or prohibit the obstruction thereof. The means by which fire lanes are designated shall be maintained in a clean and legible condition at all times and be replaced or repaired when necessary to provide adequate visibility. Fire lanes may be marked in one or a combination of methods as approved by the fire code official. Curbs. All curbs and curb ends shall be painted red with four inch (4") white lettering stating "FIRE LANE—NO PARKING". Wording may not be spaced more than fifteen feet (15') apart. Where no curb exists or a rolled curb is installed, a 6-inch (6") wide painted red stripe applied to the concrete or asphalt with four inch (4") white lettering stating "FIRE LANE—NO PARKING. "Signs. In areas where fire lanes are required, but no continuous curb is available, one of the following methods shall be used to indicate the fire lane. Option 1 : A sign twelve inches (12") wide and eighteen inches (18") in height shall be mounted on a metal post set in concrete a minimum of depth of eighteen inches (18") set back one foot (1') in from the edge of the roadway with the bottom of the sign being seven feet (7') from finished grade. Signs shall face oncoming traffic. Spacing of signs shall not exceed fifty feet (50') between signs. Signs shall be reflective material with a white color background with symbols, letters and border in red color. "FIRE LANE—NO PARKING". Option 2 : A sign twelve inches (12") wide and eighteen inches (18") in height shall be mounted on the side of a structure or other permanent fixture approved by the Fire Code Official. The bottom of the sign being seven feet (7') from finished grade. Spacing of signs shall not exceed fifty feet (50') between signs. Signs shall be reflective material with a white color background with symbols, letters and border in red color. "FIRE LANE—NO PARKING". Action required- The areas in front of hydrants and FDC shall be posted.

Miscellaneous Correction

For information only- 3206.7.2 Where located. Where exterior walls surrounding high-piled storage areas face fire apparatus access roads, such walls shall be provided with fire department access doors. 3206.7.5 Number of doors required. The required fire department access doors shall be distributed such that the lineal distance between adjacent fire department access doors does not exceed 125 feet (38 100 mm) measured center to center.

Imposed Loads

IFC 503.2.3 - Fire apparatus access roads shall be designed and maintained to support the imposed loads of fire apparatus and shall be surfaced so as to provide all-weather driving capabilities. Action required- Confirm proposed pavement will be capable of supporting 75,000-pounds.

Water Supply

IFC 507.1 - An approved water supply capable of supplying the required fire flow for fire protection shall be provided to premises upon which facilities, buildings or portions of buildings are hereafter constructed or moved into or within the jurisdiction. Action required- Confirm with Water Utilities there is adequate fire flow per IFC Table B105.1(2) with a 50% reduction allowed for an automatic fire sprinkler. Not addressed in 4/21/ 2023 comment letter.

General - Please provide MDNR Land Disturbance Permit. Does not appear to be uploaded. - Please provide SWPPP. Does not appear to be uploaded.

Sheet C.200-C.201C - For clarity, please add spot elevations for the updated retaining wall configuration on the NE corner. Does not appear to be on C.201B like indicated.

Sheet C.500 - Please update these plans with the comments provided for the Water Plans.

PLATTING. Because the proposed building crosses an existing lot line, no building permit shall be issued for the proposed building until the associated final plat (Appl. #PL20330-066) that removes said lot line has been approved and recorded. The associated final plat is currently scheduled for the May 25, 2023, Planning Commission meeting and City Council ordinance approval on June 13, 2023. This comment is inforrmational.

MECHANICAL EQUIPMENT. A note was added indicating that RTU locations will be determined at a later time for each individual tenant space for the spec building. Please note the following requirements that will be reviewed for compliance at the time of tenant finish building permit review: - To comply with City ordinance, RTUs shall be fully screened from view on all sides to a height at least equal to the height of the units being screened. Please take into account the added height of the curbs on which the RTUs will sit. - Provide manufacturer specifications for the proposed RTUs for staff to review the height(s) to check for screening compliance. These comments are information. No further action is necessary at this time.

Miscellaneous Correction

Provide cleanouts per 2018 IPC 708.1 thru 708.1.3. 4/24/23 - CO provided in yard. CO will also be required near exit from building. Deferred to MEP building permit submission.

Miscellaneous Correction

All ground and roof mounted HVAC and/or electrical generators must be screened on all 4 sides per Unified Development Ordinance Article 8, Sections 8.180.E & F. We highly recommend coordinating this with your MEP design team at this phase to avoid problems with construction. Questions on this should be directed to Hector Soto - 816.969.1600 or Hector.Soto@CityofLS.net. 4/24/23 - Not addressed. Deferred to building permit.

Miscellaneous Correction

The roundabout at Independence and Town Centre is expected to be constructed late 2023 or 2024. A connection from the proposed public sidewalk to the crosswalk ramps at the intersection needs to be constructed.

General - Please provide MDNR Land Disturbance Permit. - Please provide SWPPP.

- Please add drainage and inlet calculations to the plans. Missing drainage information will be reviewed in the next submittal.

- Match lines do not match. There are gaps and the match lines do not connect. See C.101-C.103. Please revise.

- Show on the plans the sidewalk transition on the west (C.101/C.104) of the existing sidewalk to new sidewalk with the taper length identified. On the east sidewalk connection (C.103/C.106), it shows a 4’ wide existing sidewalk connecting to a 5’ wide sidewalk and no apparent difference in width. The existing sidewalk may be 5’ wide and it is identified as 4’ wide on the plans in error. Please verify.

- Provide a complete plan for the ADA-accessible ramps. Ensure all elevation callouts, running slope callouts, and cross-slope points for construction of ADA-accessible ramps and sidewalk. Also, include details of the sidewalk through the new driveways to the development. Site specific information is required on the ADA plans. Specific elevations, slopes, etc. for each location. Missing ADA information will be reviewed in the next submittal.

Sheet C.200-C.201C - For clarity, please add spot elevations for the updated retaining wall configuration on the NE corner.

Sheets C.301-C.304 - Show design HGL on profiles. Missing on Sheet C.302. - Please verify proposed grade identification arrows. Arrow pointing to nothing on Sheet C.302. - Add a note for the compacted fill thickness of a min. 18” thickness above the top of the pipe.

Sheet C.500 - Any changes based on Water Utilities comments from their water analysis will be reviewed in the next submittal.

Sheet C.600-C.601 - Sidewalk Detail shown on Sheet C.202, but also shown at the bottom of Sheets C.600 and C.601.

Code Statement

All issues pertaining to life safety and property protection from the hazards of fire, explosion or dangerous conditions in new and existing buildings, structures and premises, and to the safety to fire fighters and emergency responders during emergency operations, shall be in accordance with the 2018 International Fire Code.

Fire Lanes - Marking

IFC 503.3 Marking. Where required by the fire code official, approved signs or other approved notices or markings that include the words NO PARKING—FIRE LANE shall be provided for fire apparatus access roads to identify such roads or prohibit the obstruction thereof. The means by which fire lanes are designated shall be maintained in a clean and legible condition at all times and be replaced or repaired when necessary to provide adequate visibility. Fire lanes may be marked in one or a combination of methods as approved by the fire code official. Curbs. All curbs and curb ends shall be painted red with four inch (4") white lettering stating "FIRE LANE—NO PARKING". Wording may not be spaced more than fifteen feet (15') apart. Where no curb exists or a rolled curb is installed, a 6-inch (6") wide painted red stripe applied to the concrete or asphalt with four inch (4") white lettering stating "FIRE LANE—NO PARKING. "Signs. In areas where fire lanes are required, but no continuous curb is available, one of the following methods shall be used to indicate the fire lane. Option 1 : A sign twelve inches (12") wide and eighteen inches (18") in height shall be mounted on a metal post set in concrete a minimum of depth of eighteen inches (18") set back one foot (1') in from the edge of the roadway with the bottom of the sign being seven feet (7') from finished grade. Signs shall face oncoming traffic. Spacing of signs shall not exceed fifty feet (50') between signs. Signs shall be reflective material with a white color background with symbols, letters and border in red color. "FIRE LANE—NO PARKING". Option 2 : A sign twelve inches (12") wide and eighteen inches (18") in height shall be mounted on the side of a structure or other permanent fixture approved by the Fire Code Official. The bottom of the sign being seven feet (7') from finished grade. Spacing of signs shall not exceed fifty feet (50') between signs. Signs shall be reflective material with a white color background with symbols, letters and border in red color. "FIRE LANE—NO PARKING". Action required- The areas in front of hydrants and FDC shall be posted.

Miscellaneous Correction

For information only- 3206.7.2 Where located. Where exterior walls surrounding high-piled storage areas face fire apparatus access roads, such walls shall be provided with fire department access doors. 3206.7.5 Number of doors required. The required fire department access doors shall be distributed such that the lineal distance between adjacent fire department access doors does not exceed 125 feet (38 100 mm) measured center to center.

Imposed Loads

IFC 503.2.3 - Fire apparatus access roads shall be designed and maintained to support the imposed loads of fire apparatus and shall be surfaced so as to provide all-weather driving capabilities. Action required- Confirm proposed pavement will be capable of supporting 75,000-pounds.

Water Supply

IFC 507.1 - An approved water supply capable of supplying the required fire flow for fire protection shall be provided to premises upon which facilities, buildings or portions of buildings are hereafter constructed or moved into or within the jurisdiction. Action required- Confirm with Water Utilities there is adequate fire flow per IFC Table B105.1(2) with a 50% reduction allowed for an automatic fire sprinkler. Not addressed in 4/21/ 2023 comment letter.

PLATTING. Because the proposed building crosses an existing lot line, no building permit shall be issued for the proposed building until the associated final plat (Appl. #PL20330-066) that removes said lot line has been approved and recorded. The initial staff review comments for the plat are due April 5, 2023. This comment is inforrmational.

MECHANICAL EQUIPMENT. A note was added indicating that RTU locations will be determined at a later time for each individual tenant space for the spec building. Please note the following requirements that will be reviewed for compliance at the time of tenant finish building permit review: - To comply with City ordinance, RTUs shall be fully screened from view on all sides to a height at least equal to the height of the units being screened. Please take into account the added height of the curbs on which the RTUs will sit. - Provide manufacturer specifications for the proposed RTUs for staff to review the height(s) to check for screening compliance. These comments are information. No further action is necessary at this time.

ACCESSIBLE ROUTE. Label the accessible routes from the accessible parking spaces to the nearest building entrances. Label the slopes and cross-slopes.

Miscellaneous Correction

Provide cleanouts per 2018 IPC 708.1 thru 708.1.3. 4/24/23 - CO provided in yard. CO will also be required near exit from building. Deferred to MEP building permit submission.

Miscellaneous Correction

1-1/2" tap not available. Change to 2".

Miscellaneous Correction

All ground and roof mounted HVAC and/or electrical generators must be screened on all 4 sides per Unified Development Ordinance Article 8, Sections 8.180.E & F. We highly recommend coordinating this with your MEP design team at this phase to avoid problems with construction. Questions on this should be directed to Hector Soto - 816.969.1600 or Hector.Soto@CityofLS.net. 4/24/23 - Not addressed. Deferred to building permit.

The roundabout at Independence and Town Centre is expected to be constructed late 2023 or 2024. A connection from the proposed public sidewalk to the crosswalk ramps at the intersection needs to be constructed.

The roundabout at Independence and Town Centre is expected to be constructed late 2023 or 2024. A connection from the proposed public sidewalk to the crosswalk ramps at the intersection needs to be constructed.

General - Please provide Engineer’s Estimate of Probable Costs. - Please provide MDNR Land Disturbance Permit. - Please provide SWPPP. - Drainage and inlet calculations must be included in the plans. - Plan Summary of Quantities does not match plans. - Match lines do not match. Please revise. - Please show all existing sidewalks on the plans. - Utilize a taper for the connection between the existing sidewalk and the proposed sidewalk where widths vary. - Please provide a complete plan for the ADA-accessible ramps. Ensure all elevation callouts, running slope callouts, and cross-slope points for construction of ADA-accessible ramps and sidewalk are shown. - Include details of the sidewalk through the proposed driveways. - Location of trash enclosures are not shown consistently throughout the plans. Arrows point to nothing.

Sheet C.051C - Sediment basin needs turf reinforcement mat to prevent erosion on the slopes.

Sheet C.100 - Please note that the concrete pavement section is required to extend 1’ behind back of curb.

Sheet C.200-C201C - Verify that there is adequate space for the trash enclosure before the slope on SE corner. - Please provide more information for the grading plan for the south side of the building. - Elevations do not seem to make sense for the gap shown in the retaining wall on the NE corner where there is a gap in the wall. Please clarify.

Sheet C.300 - Please provide size of roof drain HPDE pipe.

Sheets C301-304 - Please show design HGL on profiles. - Verify proposed grade lines. Arrows point to nothing. - Compacted fill shall be placed to a min. 18" above the top of the pipe prior to installation. Show and label the limits of the compacted fill placement in the profile view. Use hatching for clarity. - FL Pipe and Existing Grade Elevations at the bottom of the profiles do not appear correct. - Please verify that the top inlet elevations match the proposed grade elevations.

Sheet C.500 - Please denote that the New 8” Public Water Line is (By Others). - Show the public water line construction from the Public Water Plans as (By Others). - Show connecting to existing tees and installing one 8” Gate Valve (two locations) on the new private line in these plans.

Sheet L.100 - Only ornamental tree varieties are allowed within public easements. Plantings should be kept out of the detention basin slopes. Please verify and revise accordingly.

Code Statement

All issues pertaining to life safety and property protection from the hazards of fire, explosion or dangerous conditions in new and existing buildings, structures and premises, and to the safety to fire fighters and emergency responders during emergency operations, shall be in accordance with the 2018 International Fire Code.

Fire Lanes - Marking

IFC 503.3 Marking. Where required by the fire code official, approved signs or other approved notices or markings that include the words NO PARKING—FIRE LANE shall be provided for fire apparatus access roads to identify such roads or prohibit the obstruction thereof. The means by which fire lanes are designated shall be maintained in a clean and legible condition at all times and be replaced or repaired when necessary to provide adequate visibility. Fire lanes may be marked in one or a combination of methods as approved by the fire code official. Curbs. All curbs and curb ends shall be painted red with four inch (4") white lettering stating "FIRE LANE—NO PARKING". Wording may not be spaced more than fifteen feet (15') apart. Where no curb exists or a rolled curb is installed, a 6-inch (6") wide painted red stripe applied to the concrete or asphalt with four inch (4") white lettering stating "FIRE LANE—NO PARKING. "Signs. In areas where fire lanes are required, but no continuous curb is available, one of the following methods shall be used to indicate the fire lane. Option 1 : A sign twelve inches (12") wide and eighteen inches (18") in height shall be mounted on a metal post set in concrete a minimum of depth of eighteen inches (18") set back one foot (1') in from the edge of the roadway with the bottom of the sign being seven feet (7') from finished grade. Signs shall face oncoming traffic. Spacing of signs shall not exceed fifty feet (50') between signs. Signs shall be reflective material with a white color background with symbols, letters and border in red color. "FIRE LANE—NO PARKING". Option 2 : A sign twelve inches (12") wide and eighteen inches (18") in height shall be mounted on the side of a structure or other permanent fixture approved by the Fire Code Official. The bottom of the sign being seven feet (7') from finished grade. Spacing of signs shall not exceed fifty feet (50') between signs. Signs shall be reflective material with a white color background with symbols, letters and border in red color. "FIRE LANE—NO PARKING". Action required- The areas in front of hydrants and FDC shall be posted.

Miscellaneous Correction

For information only- 3206.7.2 Where located. Where exterior walls surrounding high-piled storage areas face fire apparatus access roads, such walls shall be provided with fire department access doors. 3206.7.5 Number of doors required. The required fire department access doors shall be distributed such that the lineal distance between adjacent fire department access doors does not exceed 125 feet (38 100 mm) measured center to center.

Imposed Loads

IFC 503.2.3 - Fire apparatus access roads shall be designed and maintained to support the imposed loads of fire apparatus and shall be surfaced so as to provide all-weather driving capabilities. Action required- Confirm proposed pavement will be capable of supporting 75,000-pounds.

Water Supply

IFC 507.1 - An approved water supply capable of supplying the required fire flow for fire protection shall be provided to premises upon which facilities, buildings or portions of buildings are hereafter constructed or moved into or within the jurisdiction. Action required- Confirm with Water Utilities there is adequate fire flow per IFC Table B105.1(2) with a 50% reduction allowed for an automatic fire sprinkler.

Miscellaneous Correction

Provide cleanouts per 2018 IPC 708.1 thru 708.1.3.

Miscellaneous Correction

1-1/2" tap not available. Change to 2".

Miscellaneous Correction

All ground and roof mounted HVAC and/or electrical generators must be screened on all 4 sides per Unified Development Ordinance Article 8, Sections 8.180.E & F. We highly recommend coordinating this with your MEP design team at this phase to avoid problems with construction. Questions on this should be directed to Hector Soto - 816.969.1600 or Hector.Soto@CityofLS.net.

PLATTING. Because the proposed building crosses an existing lot line, no building permit shall be issued for the proposed building until the associated final plat (Appl. #PL20330-066) that removes said lot line has been approved and recorded. The initial staff review comments for the plat are due April 5, 2023. This comment is inforrmational.

COVER SHEET. The cover sheet calls out the property's current and proposed zoning as CP-2 and PI, respectively. Revise so this just reads "Zoning: PI".

LOT LINES. On Sheet C.100, call out the existing lot line that runs through the middle of the building and note that it will be removed via replat. Similar comment for the existing lot line that defines the original detention basin configuration on the same sheet.

SIDEWALKS. Label the proposed 5' sidewalk along NE Town Centre Blvd and NE Independence Ave.

EASEMENTS. - Label the 30' storm drainage easement at the southeast corner of the common area tract. - Label the 25' storm drainage easement along the south boundary of the common area tract.

BUILDING LINES. Show and label the 20' building lines along the lot's three street frontages.

PARKING LOT. Dimension the distances between the proposed parking lot boundaries and the adjacent right-of-way and lot lines. The minimum right-of-way setback is 20'. The mininum setback from the abutting property to the south is 6'.

ACCESSIBLE ROUTE. Label the accessible routes from the accessible parking spaces to the nearest building entrances. Label the slopes and cross-slopes.

MECHANICAL EQUIPMENT. - Show the location of all RTUs on the building elevations using dashed lines. To comply with City ordinance, RTUs shall be fully screened from view on all sides by raising parapet walls to a height at least equal to the height of the units being screened. Please take into account the added height of the curbs on which the RTUs will sit. - Provide manufacturer specifications for the proposed RTUs for staff to review the height(s) to check for screening compliance.

FLOOR PLAN. Provide a floor plan showing dimensions and areas of the internal layout (i.e. office space, warehouse areas, etc.).

LANDSCAPE PLANS. - On Sheet L.100, revise the buffer/screen information for the proposed use and the adjacent use. The listed zoning districts are reversed. The proposed use should read PI and the adjoining use should read CP-2. - Revise Notes #7 and #8 on Sheet L.101 to indicate that the site shall be sodded. No seeding is allowed.

TRASH ENCLOSURES. The location of proposed trash enclosures are not consistent across all of the plan sheets. Most plan sheets show trash enclosures located close to the building between or at the end of the dock bays;the landscape plan shows the trash enclosure locations along the perimeter of the dock area boundary farthest from the building; while some plans (including the photometric plan) show a combination of the two.