Permit Application Status

B9801409


In order to schedule inspections, you need to be signed in.

 / 

Note: You can collapse and expand individual sections by clicking the header of the section you wish to collapse/expand.

Summary
B9801409
Building Permit - Commercial
Final Completion
LE GRAND APARTMENTS LLC
ALTERATION COMMERCIAL
MR PRIME BEEF SMOKERS
08/27/1998
08/31/1998
02/27/1999
05/04/1999
Locations
Contacts
SPENCER HEATING & COOLING, Address:14103 W 88TH PL  
LE GRAND APARTMENTS LLC, Address:25706 E SHADYBROOK LN  
Reviews
Review Type Outcome Est. Completion Date Completed
Internal Plan Review (Res) Approved 02/24/1999 10/29/2010
Correction

Codes Administration- It shall be the duty of the person doing the work authorized by a permit to notifiy the Building Inspections Division that such work is ready for inspection. (UBC Section 305.(c))
Correction

Codes Administration- A reinspection fee may be assessed for each inspection or reinspection when such portion of work for which inspection is called is not complete or when corrections called for are not made. ( UBC Section 305.(g))
Correction

Codes Administration- A reinspection fee may be assessed if an approved set of plans are not readily available to the inspector and the permit card is not posted at the time of the inspection. (UBC Section 305.(g))
Correction

Indicate how the oven units will be tilted to allow the waste to drain out into a floor drain, as required by the manufacture.
Correction

Clarify whether a backflow device will be installed on the water supply line.
Correction

A licensed mechanical contractor must install this proposed system. The mechnical contractor must obtain the proper permits from this office prior to the installation of any equipment.
Correction

The duct/chimney shall be firmly anchored to or otherwise supported by the building or structure. All joints shall be liquid tight or of such design that liquid will drain to the interior of the duct/chimney.
Correction

The duct/chimney must terminate a minimum of 3' above the roof structure.
Correction

The drawing submitted shows that an inline exhaust fan will be installed in the exhaust duct. This fan is sized to remove 400 cfm of air from this room. Clarify how 400 cfm will be supplied to this room.
Correction

The 1991 Uniform Mechanical Code, Section 914(b), requires that the thimble, shown on the submitted drawings, extend a minimum of 9" above and 9" below the roof structure. A clearance of 6" shall be maintained on all side of the duct as it pernetrates the roof structure.
Correction

According to the drawing submitted, the proposed duct/chimney will be of a double wall factory built type construction. Provide the manufacturer's specification on the duct/chimney to be used.
Correction

Per the 1991 Uniform Mechanical Code, Section 1002, venting systems and exhaust ducts shall not extend into or through ducts or plenums. It is our understanding that this building is using the above ceiling space as a return air plenum. The duct/chimney above the ceiling must be enclosed in a sleve of 24 guage metal with no seems and sealed at the top and bottom.
Fees
Paid Fees Amount Paid Owing Date Paid
24 BLDG Permit Fees $8.00 $8.00 Paid 08/31/1998
24 BLDG Plan Check Fees $2.50 $2.50 Paid 08/31/1998
25 Electrical Permit Fee $15.00 $15.00 Paid 08/31/1998
25 Mechanical Permit Fees $33.00 $33.00 Paid 08/31/1998
25 Plumbing Permit Fees $7.00 $7.00 Paid 08/31/1998
Outstanding Fees Amount Paid Owing Date Paid
No outstanding fees.
Totals: $65.50 $65.50 $0.00


$0.00
Inspections

There are no inspections for this permit application.

Documents & Images

No documents are currently available for viewing.

Upload Documents

Guidelines For Electronically Submitting Documents:

  • Submitted documents should be under 100MB in size.
  • Accepted file extensions:
    • pdf, jpg, xls, doc, xlsx, docx, dwg
  • All plans shall be to scale.
  • Recommended naming conventions:
    • Keep filename consistent.
    • Avoid the use of non-friendly filenames. (ex. k9dk38fj3.pdf)
    • Avoid inappropriate language in filenames.
  • Submitted documents will be stamped at the conclusion of the review.
    • The stamp will be placed in the upper right hand corner of the document. It is recommeded that this area, to the extent possible, be left blank so that no information is lost when the the stamp is applied.
Remember to click the Upload Document button. If you are applying for a New permit, make sure to click the "next step" button after you have completed the upload of documents

Select any documents you wish to provide:





Portal Home